Removing the clutch center

Joined
May 12, 2018
Messages
91
Country flag
I have my new clutch center in hand. I’m trying to remove the old clutch center from the back friction pad. The three studs that hold the clutch springs have a nut on them and they are center punched to prevent them from backing off. The nuts are 1/4W in size, very thin, and soft. I drilled the center punch marks ever so slightly with a 1/8” drill and applied head. I’m afraid of rounding the nuts. Any suggestions are greatly appreciated.
 
Well the official manual just says "remove the three nuts from the studs" which sounds simple but as you say, the nuts are very thin. You need something that has no chamfer on the end so that it gets full engagement with the nut. A tube spanner would probably be a good choice as it has a flat end and is also six sided, so less chance of rounding the nuts off. Could also try a six sided socket but grind the face flat so it gets full engagement on the nuts.

The Andover tool is for removing the clutch and Paul has already done that.

Ian
 
Well the official manual just says "remove the three nuts from the studs" which sounds simple but as you say, the nuts are very thin. You need something that has no chamfer on the end so that it gets full engagement with the nut. A tube spanner would probably be a good choice as it has a flat end and is also six sided, so less chance of rounding the nuts off. Could also try a six sided socket but grind the face flat so it gets full engagement on the nuts.

The Andover tool is for removing the clutch and Paul has already done that.

Ian
Correct on the socket with no chamfer. I was looking at buying a socket and spinning it down. I'll look for a spanner, too. Thanks!
 
Agree with Nortoniggy ...... apply some heat and go for it. On reassembly, I use red Loctite rather than center punching new "pips".

You will need a tool to compress the new rubbers. There is a thread on this in this Forum ..... https://www.accessnorton.com/NortonCommando/clutch-shock-cush-rubbers-how-to.19754/#post-294887

Slick
Pips is the correct term, eh? I'll store that in the fading memory banks. I was thinking that loctite would be a better solution. As for the tool, since I'm replacing the whole clutch pack, it should be easy enough to make at home.

After looking at the new rubbers and the RTV silicone that the PO installed in lieu of new rubbers, I'm 99% certain that is what caused the clutch plates to peen against the clutch basket on both sides. I believe it was hammering back and forth.

Thanks for the info.
 
I have my new clutch center in hand. I’m trying to remove the old clutch center from the back friction pad. The three studs that hold the clutch springs have a nut on them and they are center punched to prevent them from backing off. The nuts are 1/4W in size, very thin, and soft. I drilled the center punch marks ever so slightly with a 1/8” drill and applied head. I’m afraid of rounding the nuts. Any suggestions are greatly appreciated.
I have my new clutch center in hand. I’m trying to remove the old clutch center from the back friction pad. The three studs that hold the clutch springs have a nut on them and they are center punched to prevent them from backing off. The nuts are 1/4W in size, very thin, and soft. I drilled the center punch marks ever so slightly with a 1/8” drill and applied head. I’m afraid of rounding the nuts. Any suggestions are greatly appreciated.
I'm really hoping that there's a typo hidden in here. Otherwise I will start questioning my dedication to working on my own motorcycles as there are limits to what I'm willing to do to accomplish a mechanical task.
 
So I remembered that there's a local cycle shop in town who specializes in old Triumphs. He's a friend of mine's neighbor, so I name dropped and he removed them for me for nothing. Now I can continue without waiting for the right tool to show up next week. All is well.
 
Finally got the crush rubbers installed. With the correct homemade tool, it’s a snap. I bought 3ft of 1x1x 3/16”. Drilled three friction plates and tapped the angle iron for 5/16-18. Put two 3/8” nuts in between for spacers and it turned it into a one man operation. Clutches are installed and adjusted. The Venhill cable makes a big difference. However, the hole in the clutch handle is worn oblong. Now I need to order up a new clutch handle. It won’t delay me, though. I will adjust the primary chain, install the oil pump, and hopefully time it tomorrow. Then re-assemble it, add fluids and ride.

Being a rare 82 degree day today north of Seattle, I would have loved to have been riding.
 
Last edited:
I drilled out the hole in my clutch handle and pressed in a bronze bushing. From memory, the bushing was 5/16" OD x 3/16" ID x 1/4" long. Such bushings are available from industrial bearing suppliers.

That took out the oblong hole, and if the bushing ever becomes oblong, I'll just press in a new bushing.

Slick
 
Last edited:
Back
Top