valve spring removal tool...brilliant!!!! (2005)

Status
Not open for further replies.
FWIW, (and admittedly, not much), I just don't see the point in replacing valve seals without pulling the head, checking valves guides and valves and re-seating/lapping the valves at minimum.

I just don't see it as that much work but again, that's just me...
I will be doing this at some later...but getting at seals without pulling head will be useful...as it seems they seals can let go very shortly after installing in some cases. Frustration level and blood pressure would go through roof if head had to come off more than once in a few weeks....

Looks like I may have found a source for M7....as 50mm hex bolt full body thread
https://m.ebay.com/itm/-1-M7-1-0-or...4?pageci=14a4d3a7-ad7b-42b0-a0e7-6560d6633b60
or as all threaded rod....https://m.ebay.com/itm/-1-M7-1-0-x-...1?pageci=dda01935-7710-4482-a19e-90138e2a66c4

rivercityindustrialsupply Ebay store...will run me about $20 after shipping etc but that's acceptable to me for toolage. Will go with current plate setup first and if that hits a wall, then I have this to fall back on.
 
Update on my valve seal job. I did the smoking right side seal using the straight square rod with two long 1/4" bolts threaded through the square rod. It worked ok, but the bolt ends tended to wander off the valve end cap as the spring compressed.
Ludwig made me a very generous offer to send me out the correct thread M7 adaptor to make his tool. Well, he not only wouldn't accept even postage from me, he actually sent me the whole compressor tool!

I have just used this to perform the seal replacement on the left side. All went well. That side did not show any engine smoke on throttle blip. Yet the right side, after a test ride, had the spark plug looking grey-ish brown, while before the new seal it was oily black. Now, the Left side plug is looking black, lightly oily...so I suspect the original seal was leaking, just a much smaller amount, not noticeable as exhaust smoke. Both now have KibbleWhite viton seals. And, b/c Ludwig's tool was working so nicely, decided it was time to swap out the original intake springs (which measured under the spec free lengths listed in the manual) for fresh sets (standard type...06-7070 AN part number). Will be doing the exhaust springs tomorrow.
 
Exhaust springs now renewed. Took the opportunity to confirm presence/ condition of the insulator washer beneath the exhaust valve spring lower seat. All in good kit. Had some troubles with the rockers stepping off the pushrods while the thin rod temp spindle was in place. Took a bit of fiddling and poking the rod with a long screwdriver to reseat, but got it done. Clearances set. New spindle cover gaskets, new rocker cover gaskets ( silicone rubber reusuables). Job done.
 
Thanks Tornado
Would you mind posting a photo of what Ludwig sent you - I would like to make one
Cheers
Rob
 
Thanks Tornado
Would you mind posting a photo of what Ludwig sent you - I would like to make one
Cheers
Rob
See page 2 of this thread for some attached pic of Ludwig's tools and a pdf document on his full tutorial)(that I posted there).
 
Ludwig's photo tutorial PDF....
https://www.accessnorton.com/attachments/valve-seal1-pdf-pdf.7139/

https://www.accessnorton.com/Norton...al-tool-brilliant-2005.690/page-2#post-393677

pix
https://www.accessnorton.com/Norton...al-tool-brilliant-2005.690/page-2#post-393783
Ludwig's method for holding valve up and releasing the rocker by using a temporary thin rod in place of the spindle.
valve spring removal tool...brilliant!!!! (2005)


valve spring removal tool...brilliant!!!! (2005)


valve spring removal tool...brilliant!!!! (2005)


valve spring removal tool...brilliant!!!! (2005)




Tornado :
you do not really need M 7 .
I only suggested it as an alternative .
I know M7x1 is not very common in your part of the world , but neither is the correct ( 9/32 BSF ? ) thread .
You can cut the thread 26 TPI , or 1 mm .. ( die , lathe ..) drill and tap an old adjuster bolt , or any odd bolt that fits , weld an extention ... many ways to skin a cat .

use your imagination .
https://www.accessnorton.com/Norton...al-tool-brilliant-2005.690/page-2#post-395885

valve spring removal tool...brilliant!!!! (2005)

M5 rod , threaded in old adjuster .
 
Last edited:
Thank you Tornado and 84ok!

EDIT: You're absolutely right - many thanks to Ludwig
 
Last edited:
Status
Not open for further replies.
Back
Top