Bad backlash

Stu Bodycote

VIP MEMBER
Joined
Jun 12, 2020
Messages
1,339
Country flag
This particular bike has always had a noisy primary. The bikes done 10,000 miles, and was happy enough rattling along at that. But it clearly needed checking out.
Backlash gear incorrectly sub-assembled with spring dowl pin fitted backwards, and incorrectly positioned, so it wasn't even acting against the spring 🤦🏻‍♂️
All sorted....this bike has never sounded so quiet. I've also used him as a guinea pig, trying out some Motul 300v 15w50 in his primary side.

 
That's reassuring.
Not a design issue, but a human error in assembly.
Will this assembly error have caused any long term damage to either the gear or pin?
 
I refitted the pin the correct way round, but I wasn't confident in how secure it was, so I gave it a little weld. They tig welded quite a number of these at the factory, as Phil & I in Engine Build at the time were not happy with them. Unfortunately I've only got a mig welder here, but its done a satisfactory job...that pin is not going adrift now. I just had to nib it back a touch afterwards so it was underflush.
This sub-assembly is before my time there...so I'm in the clear lol.
No other damage...and the primary now pretty damn healthy. The customer has in fact ordered a new Norton built 961, so this bike will be going up for sale...hence the strip down and inspection.
 

Attachments

  • Bad backlash
    20230204_110608.jpg
    211.7 KB · Views: 84
Shame you didn’t do a before and after video on this!

The more I read your inputs the more I’m beginning to think there was something wrong with mine above and beyond the ‘they all do that sir’ level.
 
Last edited:
Sorry, I just didnt think to, tbh. I have an after video, I'll upload that later....but video's are a little unjust as they seem to really concentrate on the mechanical noise. Sounds better in the flesh....and this is still running a billet clutch too.
 
Last edited:
....The customer has in fact ordered a new Norton built 961, so this bike will be going up for sale...hence the strip down and inspection.
Did your customer test ride the New 961 before placing his order?
 
The pin on mine was too long and held the scissor gear away from the drive gear.

I’m beginning to think that all these engines need to be stripped and blueprinted ( unless they are marked SB of course;))
 
How was that able to back out Stu? There is a circlip and a hefty washer on mine right over the pin.


EDIT, I froze the video and could see how it can back out - carry on ;)
 
Last edited:
Sorry, I just didnt think to, tbh. I have an after video, I'll upload that later....but video's are a little unjust as they seem to really concentrate on the mechanical noise. Sounds better in the flesh....and this is still running a billet clutch too.
Here we go then. Keep in mind though, videos pick out the mechanical noise more, and this is still on a mk1 billet clutch. Taking that into consideration, I think this is now down to a very acceptable noise level.

 
Wow, that sounds like a, well, a motorcycle !

My 2018 Anniversary sounded nothing like that! And mine sounded just like many others. And I had the factory look at it twice.
 
I reckon the owner will be so pleased he’ll cancel his order for a new one:) With a billet clutch I guess it’s any early one. How does the front hub look Stu?
 
Here we go then. Keep in mind though, videos pick out the mechanical noise more, and this is still on a mk1 billet clutch. Taking that into consideration, I think this is now down to a very acceptable noise level.


Well done Stu for picking that error up I know your customer and he’ll be well chuffed. 🏍👍🏻
 
I reckon the owner will be so pleased he’ll cancel his order for a new one:) With a billet clutch I guess it’s any early one. How does the front hub look Stu?
Haha thats what I said!
It's a 2014 bike. Talon hubs...look perfect. Much like the clutch baskets falling apart, and this backlash....I'm leaning more towards an assembly error on the wheels ie over tensioning of the spokes to pull the rim in true. Wheel building is something that I really wished I had a go at whilst at Norton. It's just black magic voodoo to me....I know the theory, but the couple of times I've had a go, I've been as successful as I was at completing a rubix cube when I was young.
 
Well done Stu for picking that error up I know your customer and he’ll be well chuffed. 🏍👍🏻
Cheers, its all part of what I check during a primary inspection. I generally recommend replacing the starter motor gasket at the same time, with the rubber coated steel one's that Thiel supplies me with.
I'm looking forward to a road test later, see how she goes now.
 
Haha thats what I said!
It's a 2014 bike. Talon hubs...look perfect. Much like the clutch baskets falling apart, and this backlash....I'm leaning more towards an assembly error on the wheels ie over tensioning of the spokes to pull the rim in true. Wheel building is something that I really wished I had a go at whilst at Norton. It's just black magic voodoo to me....I know the theory, but the couple of times I've had a go, I've been as successful as I was at completing a rubix cube when I was young.
I use a spoke torque wrench and two dial indicators.
With that setup it's just down to patience. With a bit of that I think anyone can dial them in to +- ten thou and +- 5 inch pounds.
Some folks claim they get a decent job just by tensioning to a certain sound on the spokes.
I don't think that works as the properly torqued spokes all sound quite different when you plonk them.
Buchanan's wheels in USA are one of the best in the wheel building business and they use a spoke torque wrench on every wheel.

Most spoked wheels that I have checked are not torqued anywhere near equally and have very low tension on the spokes. The low tension makes for a weak wheel that is prone to spoke breakage.
The grossly uneven spoke torque is also detracting from wheel strength.
Big runout on the wheels causes lots of vibration.


Glen
 
I use a spoke torque wrench and two dial indicators.
With that setup it's just down to patience. With a bit of that I think anyone can dial them in to +- ten thou and +- 5 inch pounds.
Some folks claim they get a decent job just by tensioning to a certain sound on the spokes.
I don't think that works as the properly torqued spokes all sound quite different when you plonk them.
Buchanan's wheels in USA are one of the best in the wheel building business and they use a spoke torque wrench on every wheel.

Most spoked wheels that I have checked are not torqued anywhere near equally and have very low tension on the spokes. The low tension makes for a weak wheel that is prone to spoke breakage.
The grossly uneven spoke torque is also detracting from wheel strength.
Big runout on the wheels causes lots of vibration.


Glen
Can you show us the spoke torque wrench you use?
I’ve always been a ‘spoke tapper’ myself… maybe time to get with the programme ?!
 
Back
Top