RRussellTx - 1974 Commando 850 Project

I've always found dry shifting more crunchy than when riding. As long as you can get all four gears I wouldn't worry about it at this point. If you are still having problems when riding it is likely the hair pin needs a slight adjustment. Easy to do with bike assembled just pull the outer gearbox cover. One reason to never use gasket sealer on both sides of that gasket.
 
Another overdue update:

Finally got the Engine back from Big D Cycles last week and got it installed yesterday.
I also got the front wheel and tire ready.

Working on the rear wheel and installing the Primary side next.

After that, I'm looking for an order of assembly for all the smaller bits,

Battery Box, Ham can Air Filter, Carbs, Oil Tank, Electrical etc...
If anyone has a favorite list then I would appreciate you sharing it!


RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project
 
Install the battery tray and the horn before you go much further. It's impossible to access once you get the wheel and fender fitted. Test it first. Fit the small sub harness at the same time.
 
Last edited:
maybe its just me, but looking at that table . . . with no straps on the bike . . . makes me incredibly nervous.


that being said, wheels, front end, and everything else looks incredible. nicely done!
 
Like watching one get built at the factory. Looking good. Did you "hang" some weight with the head steady to lighten the vertical load on the isolastics?
 
That motor is the same as mine. I would disassemble it and rebuild it with new big-end shells and main bearings. None of it is rocket science. Get a workshop manual.
 
That motor is the same as mine. I would disassemble it and rebuild it with new big-end shells and main bearings. None of it is rocket science. Get a workshop manual.
Wow, you’re hardcore. You would strip an engine and replace the big end shells and main bearings immediately after receiving it back from having a professional engine rebuild ??
 
That motor is the same as mine. I would disassemble it and rebuild it with new big-end shells and main bearings. None of it is rocket science. Get a workshop manual.
As FE said - why would you do that to newly rebuilt engine? Watchoo been sniffin' Willis? :rolleyes: :rolleyes:
 
Finally getting back on the project again.

I have a 1950's oven I use for powder coating that came in handy for the chain. I really want to save the factory chain if I can but it was super stuck from all the years sitting. I have had it soaking in various fluids for several months and the last step was to heat some gear oil and drop in the chain. I got the oil up to about 350f which is the top end of what the oil can tolerate and dropped it in. It bubbled like the pic below for a couple of minutes - I did not expect that...

The chain was very flexible before it was dipped and shows no wear at all, although I was hoping it would have cleaned up a little better.
Hopefully it will hold up!

I also bought some electrical goodies from Greg so I can build a new harness. I was going to start on that next but decided I needed to get more components in place before I could make much progress. I also have more chrome and polished aluminum bits to shine up which will slow things down again.

I feel like I'm on the down hill side of the project but that's probably wishful thinking...

I'll need to get some help getting it off my (very handy) sketchy table soon!
I at least strapped it down before I hung too much off the back end...




RRussellTx - 1974 Commando 850 Project


RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project
RRussellTx - 1974 Commando 850 Project

RRussellTx - 1974 Commando 850 Project
 
I have a 1950's oven I use for powder coating that came in handy for the chain. I really want to save the factory chain if I can but it was super stuck from all the years sitting. I have had it soaking in various fluids for several months and the last step was to heat some gear oil and drop in the chain. I got the oil up to about 350f which is the top end of what the oil can tolerate and dropped it in. It bubbled like the pic below for a couple of minutes - I did not expect that...

The chain was very flexible before it was dipped and shows no wear at all, although I was hoping it would have cleaned up a little better.
Hopefully it will hold up!


View attachment 120339

View attachment 120341
Chains are so inexpensive, I'm not sure I'd have re-used one on a major project...

Did you measure the chain "sag" when laid out "laying down" on it's outer edges, to see how much "bow" is evident from wear?

Don't do this...
IMG_0110.JPG
 
Chains are so inexpensive, I'm not sure I'd have re-used one on a major project...

Did you measure the chain "sag" when laid out "laying down" on it's outer edges, to see how much "bow" is evident from wear?

Don't do this...
View attachment 120350
They were shit when new… compared to newer chains they’re even shitter than that now !!

I used to run Reynolds GP chains, the best you could get, on my T140 back in t’ day… I had to adjust it EVERY RIDE.

I run a Chain Man IWIS on my current T140 and cannot recall when I last adjusted it. The cNw O ring chain on my Commando requires even less !
 
Last edited:
They were shit when new… compared to newer chains they’re even shitter than that now !!

I used to run Reynolds GP chains, the best you could get, on my T140 back in t’ day… I had to adjust it EVERY RIDE.

I run a Chain Man IWIS on my current T140 and cannot recall when I last adjusted it. The cNw O ring chain on my Commando requires even less !
Well, these bits of knowledge are why I post and they are much appreciated, but it usually ends up costing me more $$!!

Is the cNw o-ring the same as the X ring that requires a conversion?

I will alway spend the money on things that are hard to replace later and skimp a little more on stuff that is easier to swap out later. Safety and reliability are exceptions…

Thanks again for the great responses!
They are always very helpful.
 
Well, these bits of knowledge are why I post and they are much appreciated, but it usually ends up costing me more $$!!

Is the cNw o-ring the same as the X ring that requires a conversion?

I will alway spend the money on things that are hard to replace later and skimp a little more on stuff that is easier to swap out later. Safety and reliability are exceptions…

Thanks again for the great responses!
They are always very helpful.
The cNw kit IS an X ring… not O ring, that was my mistake.

If you’re wanting to limit the dollar damage to your wallet, especially if your sprockets are good, you could get an IWIS chain from this chap. However, I’ve no idea what the logistics time, cost and tariff situation would be these days…

 


Write your reply...
Back
Top