New Head Steadys

Status
Not open for further replies.
Joined
Dec 10, 2008
Messages
7,253
Country flag
First twenty head steadys are nearly ready to ship. Just waiting on the last of the harware to arrive. Jim [PS The head steady on the bike is a blem]


New Head Steadys


New Head Steadys


New Head Steadys
 
The head steadys are going to be on CNW's website soon. They can be purchased from them or you can buy directly from me. I think I presently have eight that are not yet spoken for and the next run of about 50 will be available in 4 to 6 weeks. Jim
 
comnoz said:
The head steadys are going to be on CNW's website soon. They can be purchased from them or you can buy directly from me. I think I presently have eight that are not yet spoken for and the next run of about 50 will be available in 4 to 6 weeks. Jim

And to ask the obvious... how much?
 
I see the engine ground wire is not attached. Will there be a tapped hole on the head steady or a good way to attach it somewhere? There isn't much room for the lug around the center allen screw where it normally goes.
 
I have always thought that attaching the ground wire to the part of the motor that shakes the most was a pretty poor plan. I would advise attaching the red ground wire in the picture to the top bracket bolt and then installing a new ground wire. [10 gauge] from one of the oil filter mounting bolts up to the lug near the battery. This will eliminate vibration failure of the ground wire. Jim
 
comnoz said:
$295.00 with stainless hardware

I may have one of these set aside already for me by Matt at CNW. This is the last piece to my MKIII puzzle that is missing.
 
Ludwig, what exactly is so hopeless on this type of headsteady?
 
nortonspeed said:
Ludwig, what exactly is so hopeless on this type of headsteady?

He believes that the motion of the engine/drivetrain should move in a purely vertical motion and that any of these link type head steadies introduce an arc to the movement (despite this being virtually null).

How was that?
 
Swooshdave, see what you mean. But what difference in (tenth of) mm are we talking about at the end of the arc and will this influence the steering?
 
ludwig said:
swooshdave said:
nortonspeed said:
Ludwig, what exactly is so hopeless on this type of headsteady?

He believes that the motion of the engine/drivetrain should move in a purely vertical motion and that any of these link type head steadies introduce an arc to the movement
the arc movement is there , but purely theoretical and totally irelevant .
I tried to explain earlier that everybody with basic metal working skills can make a perfect , one piece headsteady in an afternoon for less than 5 dollars .
What does this headsteady do : it prevents lateral movement while allowing vertical movement , using an existing fixing point of the frame .
You can achieve exactly the same goal without using heim joints .
But apparenty , if it doesn't look high tech , It isn't shiney and doesn't costs a lot of money , ( some ) people just can't believe it will work .
Trying to convince people of an alterative seems futile and hopeless..
Having said that , this new headsteady looks very nice and well made .
It shure looks strong enough to moore an aircraft carrier .
I am convinced it will do an exellent job , but IMO it is a typical case of overengineering .

But the advantage of the jointed head steadies is a lower coefficient of friction that neither isolastics or your design provides. Am I correct?
 
Ludwig, I would love to see your design. Putting up with the load is easy. I put a lot of miles on my bike and have found dealing with the pounding from the vibration is not. Jim
 
comnoz said:
Ludwig, I would love to see your design. Putting up with the load is easy. I put a lot of miles on my bike and have found dealing with the pounding from the vibration is not. Jim

From ludwig's posting on Britbike

New Head Steadys

New Head Steadys

New Head Steadys

New Head Steadys

New Head Steadys

New Head Steadys


I think it's an interesting concept. I don't like the fact that it's set up with a clearance (PTFE) to make it work and I hope the offset design isn't a problem. But I'm not an engineer.
 
My own homemade mount is similar to the new offer above, based on the Taglieri version, mounted from the standard steady position. Question I have is what do the experts think about lack of support with these designs? On and Off the wheels there is noticeable vertical movement (at least 1/10") since the original exhaust rubbers and the Norvil ISO provided some added support as did the spring device on Mk3's. Mine works well but I wondered what the opinions are out there?
 
Keith,I made the same head steady but mounted a couple of springs off it, unfortunatly they dont pull straight up so I don't know how effective they really are and I didn't notice any difference with or without the springs,steady works well though.
 
Received mine today. It's really well built. Wasn't expecting the rubber seals...
 
Status
Not open for further replies.
Back
Top