| View previous topic :: View next topic |
| Author |
Message |
Dana
Joined: 07 Nov 2003
Posts: 124
Location: Folsom, CA (not the prison)
|
 Posted: Sat May 01, 2004 7:45 pm Post subject: Petcock question |
 |
|
Ok, this is a real newbie question but I can't find it anywhere, and I wasn't paying attention when they came apart ...
Which sides are the main/reserve petcocks on ....  .. does it really make a difference? |
|
| Back to top |
|
 |
illf8ed
Joined: 30 Dec 2003
Posts: 474
|
| Posted: Sun May 02, 2004 6:41 am Post subject: Petcocks |
|
|
Good Morning Dana,
On my '72 the reserve is on the right. Do you have a parts manual for your '75. Look at the gas tanks and see what side they have the "reserve" sticker on.
I'm off for the Mt Hamilton ride this morning. |
|
| Back to top |
|
|
Dana
Joined: 07 Nov 2003
Posts: 124
Location: Folsom, CA (not the prison)
|
| Posted: Sun May 02, 2004 10:34 pm Post subject: |
|
|
Hi David,
I hope the ride was nice! Great weather for it.
I put it on the right before I saw your answer. I figured I would want to pull the clutch in if it went dead, which leaves the other hand free to reach down and do its thing.
BTW ... I installed the battery, tank, petcocks, fuel line, yata yata, and gave the beastie a few good swift kicks. I was quite surprised when I actually got a few pops and sputters (no pipes).
After a premature celebration, I put on one of my Dunstalls (cleaned up very nicely on my wire wheel). Tomorrow I install the other.
Oh yes, I forgot to mention ... I left a gallon of fuel on my concrete driveway (it evaporated quickly in the 95 degree sun). I don't think I have the Mikuni's lines and other settings right. Any ideas where I can find a good site for the carbeuretically challenged ... I've been to th Sudco site, but I need more than a blowup ... the fuel was pouring out of the (overflow?) at the bottom  Next time ... I take more pictures
... getting close! |
|
| Back to top |
|
|
Ron L
Joined: 27 Feb 2004
Posts: 1149
Location: Ohio
|
| Posted: Mon May 03, 2004 3:21 am Post subject: |
|
|
Dana,
You seem to have already found my biggest gripe with Mikuni's. Let fuel stand in the float bowl for a couple weeks and the float will stick. If you are lucky, a sharp rap on the side of the bowl will stop it. Then ride it enough to let the fresh fuel flush the needle and rods the floats ride on.
If not, you will have to take apart the float bowl and thoroughly clean the needle and seat and the rods the double floats ride on. It seems that with today's fuels, the rods get gummy very easily.
I have a few bikes in the garage and seem to have less time than ever to ride. This is not good for the bikes or me! Those that ride with the Mikuni's on a regular basis don't seem to have as much problem.
As far as which side is reserve, it doesn't matter. The factory manuals seem to show reserve on the right. However, I have seen at least one showing it on the left, and at least a couple bikes which were set up at the dealer on the left.
Ron L |
|
| Back to top |
|
|
illf8ed
Joined: 30 Dec 2003
Posts: 474
|
| Posted: Mon May 03, 2004 5:08 am Post subject: petcocks` |
|
|
Hi Dana,
The ride had perfect weather, 22 Nortons showed up and no roadside repairs or crashes. As you said the temperatures were in the 90s. Gar took me to a ranch just off Mines Road where an acquaintence has several older Brit machines including a '59 Velocette with 200cc flat opposed engine (like a BMW). He said there were very few made. I know I haven't seen or heard of this model before. I'm going to have to do a search.
I mentioned your "which side for reserve" to Phil Radford. He said he like reserve on the left so that you can stay on the gas whil reaching to flip on the reserve. Makes sense to me and I know when I run out I end up trying to turn the right side petcock on with my left hand. |
|
| Back to top |
|
|
debby
Joined: 15 Apr 2004
Posts: 898
Location: Boulder, CO
|
| Posted: Mon May 03, 2004 8:29 am Post subject: |
|
|
On both of my Nortons reserve was on the right. I think I'll swap the petcocks around though. Would be much more convenient to have reserve on the left. As David pointed out, when it runs out you need to keep your hand on the throttle. Reaching over to the right petcock with your left hand while riding is very hard to do!
Regarding the gushing Mikuni carb - I had that happen on my old suzuki recently. I was shocked to see how fast the gas was pouring out! In this case rapping the float bowl didn't stop it but shutting the engine off and flushing the carb by draining the bowl did. I had to do it several times.
That also happened on my Norton recently. Those amals don't have overflow tubes so it just filled the cylinder full of gas. Had to kick it over with the plugs out to flush out the gas. It shot out like a geyser. Funny thing was the bike would still idle though it didn't run above idle. I guess they all need to be ridden regularly...
Debby |
|
| Back to top |
|
|
Dana
Joined: 07 Nov 2003
Posts: 124
Location: Folsom, CA (not the prison)
|
| Posted: Mon May 03, 2004 11:23 pm Post subject: |
|
|
Thanks folks,
I think I know the fuel problem without even looking. I recall someone (no names ... but not on this list) was helping me set it up and told me to make sure the tab was horizontal.
That seemed strange because I had to bend the tab a bunch (and no ... I didn't stop to think about the tab and float's functions ... I just followed blindly). I believe he really meant to say the floats should be horizontal.
Well, I'm guessing I need to re-bend the tab back up so the jet shuts off the flow as it should ... D'uh!
BTW ... everything inside my Mikuni is either brand spankin new, or cleaned and shiny. That includes all the jets, needle, etc. (even that durned hard-to-get-at air jet --- boy was that ever fun to remove after 20 years of being gunked up).
Stay tuned folks ... pipes going on this week. |
|
| Back to top |
|
|
dynodave
Joined: 28 May 2003
Posts: 139
Location: USA
|
| Posted: Tue May 04, 2004 2:25 am Post subject: |
|
|
Last edited by dynodave on Mon Apr 11, 2005 5:16 pm; edited 1 time in total |
|
| Back to top |
|
|
kenny
Guest
|
| Posted: Tue May 04, 2004 5:50 am Post subject: |
|
|
It's funny but on my 68 commando the reserve is on the left; I just thought it was 'British backward' just like the shifter and brake.
I just remember "left for leftover gas" "right for run".
My float has been sticking lately also; dripping gas all over my points cover. I hope a little spark from my points doesn't make things too exciting. |
|
| Back to top |
|
|
|
Norton Commando Forum by Corporate Pages Web hosting using phpbb
The Unapproachable Norton Commando
At the end of 1967 the Norton Commando was announced.
The Norton Commando was greeted with a certain amount of scepticism because on first sight the commando appeared to comprise of the old Norton Dominator twin cylinder engine mounted at an inclined angle in a set of new cylinder parts.
It was not realized that the new Norton Commando Isolastic method of engine suspension damped out all engine vibration and produced a machine which had uncanny smoothness for a vertical twin. In due course the critics were silenced and the Norton Commando had the distinction of being regarded as the first of todays so called superbikes. There can be little doubt that the original design concept of the Norton Commando has proved correct, since comparatively few modifications of any real consequence have been made since production commenced during 1968.
Now nearly 40 years later Norton Commando riders like us are a breed of our own, and as far as we are concerned its still more fun to go for a blat on the old Norton Commando, and fast. As a Norton Commando owner and enthusiast, my goal here is to promote and give credit to those who keep the Norton name going.
It is more deserving to give credit to the Commando itself, for after all these years it continues to be respected. The original Commando designers like John Favill are those who deserve the credit for developing this incredible motorcycle.
The Norton Commando Roadster and Interstate of the late seventies, never died. Although the Norton Villiers factory dispersed the tradition lived on. Today Kenny Dreer in the USA is developing the new 952 CC Norton. What a great looking bike this is, and its engineering is still based on the original layout. It will be interesting to see how the new 952CC Norton does in todays tough motorcycle market. One thing is for sure, I would own one if I could afford it.
