Norton Commando
Jerrydoe.com  Forum Home  Norton Commando Forum  Photos  [FAQ]  [Search]  [Memberlist]   
 [Profile]  [Check your private messages]  [Register]  [Log in] 
Centre Stand Spring Replacement
Goto page Previous  1, 2
 
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles.
View previous topic :: View next topic  
Author Message
dynodave



Joined: 28 May 2003
Posts: 139
Location: USA

PostPosted: Tue Oct 26, 2004 3:59 am    Post subject: 71 side stands Reply with quote

The exact bike vin that the outboard side stand might not be a exactically at the 200000 point and is likely to have started earlier. Neither is this the point of debate, but clearly the MY 71 bike that I fixed and Debbie's is also an inboard type. For lack of a better name I call it the 71 inboard type. It generally was not done in MY 70, most 70 were with the rear crossbar, and then 72 starting with 200000 had gone outboard.
As model years and particular body styles were not released at the same time, the line gets blurry for some of these updates. Sure you will see particular bike that don't fit the clean definitions such as this one.
Otherwise I am just reporting the results of my first hand inspections of MANY hundreds of commandos.
I'm just telling the list what I have seen.
generally.... it is as follows
68-70 style
71 inboard
72+outboard

I
Back to top
nortonfan



Joined: 24 Dec 2003
Posts: 362
Location: Brisbane, Australia

PostPosted: Thu Oct 28, 2004 3:38 am    Post subject: Reply with quote

norbsa48503 wrote:

Now hook the spring to both ends with the stand bolts still out. than pull back on the stand to line up the bolt holes.


So getting back to my original question.......

norbsa is the only person to suggest a method, so can we call it the best, as it probably is ?
Back to top
Derek Wilson



Joined: 25 Jun 2004
Posts: 86
Location: The Great White North

PostPosted: Thu Oct 28, 2004 4:19 am    Post subject: Reply with quote

Norbsa's method sounds like about the only elegant way of doing it. I have also heard of clamping one of the spring hooks of the spring in a vise and flexing the spring back & forth, while placing washers between the open coils. Once you have the spring in position, pull the washers out one by one.
I never seem to have enough washers on hand, so I usually get ham-fisted and use a pair of vise grips (and some touch up paint!).

Cheers,

Derek
Back to top
Jason Curtiss



Joined: 14 Jun 2003
Posts: 667
Location: HOUSTON, TEXAS

PostPosted: Thu Oct 28, 2004 7:22 am    Post subject: Reply with quote

I have used the NORBSA method of attaching the center stand spring and can report that it works. I've tried the washer method that Derek mentioned but have not yet been successful.

Jason
Back to top
nortonfan



Joined: 24 Dec 2003
Posts: 362
Location: Brisbane, Australia

PostPosted: Thu Oct 28, 2004 11:48 am    Post subject: Reply with quote

Derek,

I can relate to your method, with my back problem, I found it frustrating.

It also seems you may have read the NOC UK notes as well.

I have always hooked one end into the "gearbox cradle" point & then used a screwdriver to "stretch" it over & around the centre stand crosspiece. Sometimes it seems to go on easy.....but other times........
And as you have mentioned, you mess up the paint job.

Jason seems to think norbsa's idea is an OK method, so it still seems the best solution to an annoying little job. I will definitely try that way when my aprts arrive back from the powder coaters.
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles. All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

The Unapproachable Norton Commando

At the end of 1967 the Norton Commando was announced.

The Norton Commando was greeted with a certain amount of scepticism because on first sight the commando appeared to comprise of the old Norton Dominator twin cylinder engine mounted at an inclined angle in a set of new cylinder parts.

It was not realized that the new Norton Commando Isolastic method of engine suspension damped out all engine vibration and produced a machine which had uncanny smoothness for a vertical twin. In due course the critics were silenced and the Norton Commando had the distinction of being regarded as the first of todays so called superbikes. There can be little doubt that the original design concept of the Norton Commando has proved correct, since comparatively few modifications of any real consequence have been made since production commenced during 1968.

Now nearly 40 years later Norton Commando riders like us are a breed of our own, and as far as we are concerned its still more fun to go for a blat on the old Norton Commando, and fast. As a Norton Commando owner and enthusiast, my goal here is to promote and give credit to those who keep the Norton name going.

It is more deserving to give credit to the Commando itself, for after all these years it continues to be respected. The original Commando designers like John Favill are those who deserve the credit for developing this incredible motorcycle.

The Norton Commando Roadster and Interstate of the late seventies, never died. Although the Norton Villiers factory dispersed the tradition lived on. Today Kenny Dreer in the USA is developing the new 952 CC Norton. What a great looking bike this is, and its engineering is still based on the original layout. It will be interesting to see how the new 952CC Norton does in todays tough motorcycle market. One thing is for sure, I would own one if I could afford it.