Norton Commando
Jerrydoe.com  Forum Home  Norton Commando Forum  Photos  [FAQ]  [Search]  [Memberlist]   
 [Profile]  [Check your private messages]  [Register]  [Log in] 
To prime or not to prime

 
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles.
View previous topic :: View next topic  
Author Message
Brewer



Joined: 01 Oct 2007
Posts: 31
Location: Mandurah, Western Australia

PostPosted: Wed Jun 25, 2008 11:43 pm    Post subject: To prime or not to prime Reply with quote

Hi All,
I know there has been a lot of discusion about different procedures in how to paint commando barrels. but I am a bit confused about whether the barrel needs to be primed with a suitable primer after they are stripped of old paint and blasted with glass bead blasting. and then painted with black paint.
Does the barrell really need to be painted with heat-proof paint or not?

Also is it best to paint the barrel after they have been rebored if needed?

Thanks for your opinions.

Brewer.
Back to top
L.A.B.
Moderator


Joined: 20 Nov 2004
Posts: 1842
Location: Norfolk, UK

PostPosted: Thu Jun 26, 2008 12:05 am    Post subject: Reply with quote

Personally, I just use a normal heat resistant paint and no primer, but I'm sure there will be some different opinions on this one? I have used ordinary enamel spray paint before now, and that was OK.
Back to top
ML



Joined: 29 Jul 2007
Posts: 43
Location: Melbourne, Australia

PostPosted: Thu Jun 26, 2008 2:56 pm    Post subject: Reply with quote

Brewer,
No need to prime iron barrels, but you must use a good quality heat resistant engine enamel. The barrels must be clean and dry. Apply several coats as per can instructions and if the barrels are off the bike, use the missus hair dryer to warm the barrels a bit before spraying and afterwards to assist the cure. Any AutoOne store will have a good brand and expect to pay about $14 for a can big enough to do a V8 block.

Mick
Back to top
Brewer



Joined: 01 Oct 2007
Posts: 31
Location: Mandurah, Western Australia

PostPosted: Sun Jun 29, 2008 8:37 pm    Post subject: Reply with quote

Ok, thanks guys. I have bought a can of HVT (PJ1) Engine Enamel paint. I will use that after the barrel has been glass bead blasted.

Thanks for all advice.

Brewer.
Back to top
mikie3117



Joined: 25 Feb 2008
Posts: 51

PostPosted: Mon Jun 30, 2008 5:40 am    Post subject: Reply with quote

Hi. You are getting some great advice on barrel prep. Do not use your oven or your wife's oven mitts to "cure" the paint job. The vapors gagged even the cat and I had to buy new mitts! Twisted Evil
Mike
Back to top
71basketcase



Joined: 21 Feb 2005
Posts: 79
Location: CapeCod

PostPosted: Sun Jul 06, 2008 6:14 am    Post subject: Reply with quote

Quote:
Do not use your oven or your wife's oven mitts to "cure" the paint job. The vapors gagged even the cat and I had to buy new mitts!


AND....... I'd have to find a new place to live once my wife found out!
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles. All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

The Unapproachable Norton Commando

At the end of 1967 the Norton Commando was announced.

The Norton Commando was greeted with a certain amount of scepticism because on first sight the commando appeared to comprise of the old Norton Dominator twin cylinder engine mounted at an inclined angle in a set of new cylinder parts.

It was not realized that the new Norton Commando Isolastic method of engine suspension damped out all engine vibration and produced a machine which had uncanny smoothness for a vertical twin. In due course the critics were silenced and the Norton Commando had the distinction of being regarded as the first of todays so called superbikes. There can be little doubt that the original design concept of the Norton Commando has proved correct, since comparatively few modifications of any real consequence have been made since production commenced during 1968.

Now nearly 40 years later Norton Commando riders like us are a breed of our own, and as far as we are concerned its still more fun to go for a blat on the old Norton Commando, and fast. As a Norton Commando owner and enthusiast, my goal here is to promote and give credit to those who keep the Norton name going.

It is more deserving to give credit to the Commando itself, for after all these years it continues to be respected. The original Commando designers like John Favill are those who deserve the credit for developing this incredible motorcycle.

The Norton Commando Roadster and Interstate of the late seventies, never died. Although the Norton Villiers factory dispersed the tradition lived on. Today Kenny Dreer in the USA is developing the new 952 CC Norton. What a great looking bike this is, and its engineering is still based on the original layout. It will be interesting to see how the new 952CC Norton does in todays tough motorcycle market. One thing is for sure, I would own one if I could afford it.