Norton Commando
Jerrydoe.com  Forum Home  Norton Commando Forum  Photos  [FAQ]  [Search]  [Memberlist]   
 [Profile]  [Check your private messages]  [Register]  [Log in] 
Transmission work

 
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles.
View previous topic :: View next topic  
Author Message
ntst8



Joined: 14 Feb 2004
Posts: 117
Location: New Zealand

PostPosted: Mon Aug 30, 2004 12:00 pm    Post subject: Transmission work Reply with quote

I am planning some work on the transmission, lipped seals on kick start and gear lever to deal to oil smear on case after riding the windy stuff and Dyno Daves clutch rod seal to deal with a sticky clutch. I have also seen in the British Spares (NZ) special products catalogue the “Commando clutch pushrod kit” including needle thrust bearing, ball bearing etc. I would be interested in any comments on whether this is necessary, desirable, overkill?

Thanks

PS thanks to those who responded the electrical query a while back, still have not resolved it but it is quite rideable and spare time has been used for riding rather than tweaking of late.
Back to top
norbsa48503



Joined: 07 Apr 2004
Posts: 995
Location: Flint, Michigan

PostPosted: Mon Aug 30, 2004 12:14 pm    Post subject: Reply with quote

The use of the diaphram spring on the Commando clutch kind of makes this an un-needed modification. It's a real good thing when running multi-spring pressure plates like the old Atlas clutches. The pancake needle bearing needs to be packed with grease but it only turns when the clutch is disengadged. You might want to check your layshaft bearing mine went out this summer and the only sign was a nasty leak at the kick start seal. The bikes talken to ya, so you best hear. norbsa
Back to top
ntst8



Joined: 14 Feb 2004
Posts: 117
Location: New Zealand

PostPosted: Mon Aug 30, 2004 12:31 pm    Post subject: Transmission Work Reply with quote

Thanks, the gearbox internals haven't been touched since i have had the bike (20yrs) so sounds like time for a once over. It has been ridden hard (by my standards anyway) riding with modern machines in the last couple of years.
Back to top
norbsa48503



Joined: 07 Apr 2004
Posts: 995
Location: Flint, Michigan

PostPosted: Mon Aug 30, 2004 12:57 pm    Post subject: Reply with quote

The re-build kit from Norvil in England is the best buy for this. Cost me 200.00 US with shipping. Has the new superblend roller bearing all bushes and seals and springs. Thier part # 08-5002 this kit does not come with two things it should though, 04-0033 the pin for the pawl and 04-0132 a needed seal. If I were you I would also order the kick start pawl they wear. You will need some porpose built tools so I hope you have a lathe handy. norbsa
Back to top
Guest






PostPosted: Mon Aug 30, 2004 2:12 pm    Post subject: Reply with quote

Thanks again, will look at that. When it comes to lathe work etc i leave it to the experts - I have neither the patience nor the skill so would rather work a few extra hours at what i am good at to pay someone who knows what they are doing.
Back to top
dynodave



Joined: 28 May 2003
Posts: 139
Location: USA

PostPosted: Mon Aug 30, 2004 4:40 pm    Post subject: Reply with quote

Arrow

Last edited by dynodave on Mon Apr 11, 2005 5:05 pm; edited 1 time in total
Back to top
norbsa48503



Joined: 07 Apr 2004
Posts: 995
Location: Flint, Michigan

PostPosted: Tue Aug 31, 2004 7:10 am    Post subject: Reply with quote

Hey Dave, The kit from Norvil is just for a standard rebuild of the trans and has no pancake needle bearing. norbsa
Back to top
dynodave



Joined: 28 May 2003
Posts: 139
Location: USA

PostPosted: Tue Aug 31, 2004 7:43 am    Post subject: Reply with quote

Arrow
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles. All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

The Unapproachable Norton Commando

At the end of 1967 the Norton Commando was announced.

The Norton Commando was greeted with a certain amount of scepticism because on first sight the commando appeared to comprise of the old Norton Dominator twin cylinder engine mounted at an inclined angle in a set of new cylinder parts.

It was not realized that the new Norton Commando Isolastic method of engine suspension damped out all engine vibration and produced a machine which had uncanny smoothness for a vertical twin. In due course the critics were silenced and the Norton Commando had the distinction of being regarded as the first of todays so called superbikes. There can be little doubt that the original design concept of the Norton Commando has proved correct, since comparatively few modifications of any real consequence have been made since production commenced during 1968.

Now nearly 40 years later Norton Commando riders like us are a breed of our own, and as far as we are concerned its still more fun to go for a blat on the old Norton Commando, and fast. As a Norton Commando owner and enthusiast, my goal here is to promote and give credit to those who keep the Norton name going.

It is more deserving to give credit to the Commando itself, for after all these years it continues to be respected. The original Commando designers like John Favill are those who deserve the credit for developing this incredible motorcycle.

The Norton Commando Roadster and Interstate of the late seventies, never died. Although the Norton Villiers factory dispersed the tradition lived on. Today Kenny Dreer in the USA is developing the new 952 CC Norton. What a great looking bike this is, and its engineering is still based on the original layout. It will be interesting to see how the new 952CC Norton does in todays tough motorcycle market. One thing is for sure, I would own one if I could afford it.