Norton Commando
Jerrydoe.com  Forum Home  Norton Commando Forum  Photos  [FAQ]  [Search]  [Memberlist]   
 [Profile]  [Check your private messages]  [Register]  [Log in] 
newbie needs some advice before he gets in to the beast

 
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles.
View previous topic :: View next topic  
Author Message
mc1011



Joined: 25 Oct 2008
Posts: 26

PostPosted: Tue Oct 28, 2008 3:43 am    Post subject: newbie needs some advice before he gets in to the beast Reply with quote

hi all i'm a newbie norton owner 75 850 commando and like newbies i have a million question! any ways i love the bike and looking at this forum you guys will be a great help.my plans are to re-wire new main harness and tri-spark to replace boyer and 2 new 932 carbs and cables.parts are on there way just waiting to start.tell me if i'm approaching this in the right order.1st pull old carbs then with new wiring harness strip old harness as i plug new one in to play.add some new coils and wire in tri-spark ing then last install carbs.sounds easy but i just want to be prepared . would this be the proper order thanks newbie mike
Back to top
gahi



Joined: 01 Apr 2008
Posts: 18
Location: Winter Park, CO

PostPosted: Tue Oct 28, 2008 5:42 am    Post subject: Reply with quote

I think you should tackle one piece at a time. Its reall easy to tear stuff apart, than get overwhelmed.
Start by pulling the gas tank and seat. Than make note of how the throttle cables are routed. Pull the caps off the carbs, using the two phillips head screws on top. than pull the throttle and choke slides out by pulling straight up. They should just slide out.
To remove the carbs themselves, find the correct size allen wrench, and remove the intakes from the head. It is almost impossible to get the carbs off the intakes while its all on the bike. I had good luck grinding down the short end of the allen wrench a little bit to make it easier to get in to place. When replacing the carbs, do not over-tighten the nuts that hold the carbs to the intake. You could ruin your brand new carbs by bending the bodies of the carb.
When doing the wiring, its going to be hard to unplug one as you plug in the other. A good way to tackle this is with a roll of masking tape and a sharpie. Put a piece of tape on each side of the connector and label it. Than go a little at a time.
Start with those two. would be my advice. That way you dont get in so deep you forget what goes where and lose interest.
Back to top
mikie3117



Joined: 25 Feb 2008
Posts: 57

PostPosted: Tue Oct 28, 2008 6:17 am    Post subject: Reply with quote

Welcome newbie. Great advice from Gahi about doing one task at a time. Get the interference out of the way (tank/seat) I have always had a shortened allen wrench for the carbs available. You will find lots of opinions in this forum but I would find a box for the Amals and buy a single Mikuni kit. You will still need the "special" allen wrench.

Plan out what you want to do with the wiring. There are some really neat electronic gizmos that can make wiring much simpler. Draw it out on paper first. Replacing the stock connectors will pay dividends later. They are famous for causing late night road side emergencies.

Mike
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Norton Commando Forum Index -> Norton Commando Motorcycles. All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

The Unapproachable Norton Commando

At the end of 1967 the Norton Commando was announced.

The Norton Commando was greeted with a certain amount of scepticism because on first sight the commando appeared to comprise of the old Norton Dominator twin cylinder engine mounted at an inclined angle in a set of new cylinder parts.

It was not realized that the new Norton Commando Isolastic method of engine suspension damped out all engine vibration and produced a machine which had uncanny smoothness for a vertical twin. In due course the critics were silenced and the Norton Commando had the distinction of being regarded as the first of todays so called superbikes. There can be little doubt that the original design concept of the Norton Commando has proved correct, since comparatively few modifications of any real consequence have been made since production commenced during 1968.

Now nearly 40 years later Norton Commando riders like us are a breed of our own, and as far as we are concerned its still more fun to go for a blat on the old Norton Commando, and fast. As a Norton Commando owner and enthusiast, my goal here is to promote and give credit to those who keep the Norton name going.

It is more deserving to give credit to the Commando itself, for after all these years it continues to be respected. The original Commando designers like John Favill are those who deserve the credit for developing this incredible motorcycle.

The Norton Commando Roadster and Interstate of the late seventies, never died. Although the Norton Villiers factory dispersed the tradition lived on. Today Kenny Dreer in the USA is developing the new 952 CC Norton. What a great looking bike this is, and its engineering is still based on the original layout. It will be interesting to see how the new 952CC Norton does in todays tough motorcycle market. One thing is for sure, I would own one if I could afford it.